AXP202 DATASHEET PDF

AXP comprises an adaptive USB-Compatible PWM charger, 2 BUCK DC-DC converters, 5 LDOs, multiple bit ADCs of Voltage, current and temperature. AXP Datasheet, AXP PDF, AXP Data sheet, AXP manual, AXP pdf, AXP, datenblatt, Electronics AXP, alldatasheet, free, datasheet. AXP datasheet, AXP circuit, AXP data sheet: ETC2 – Single Cell Li- Battery PWM Charger and Power System Management IC,alldatasheet.

Author: Tami Mikalabar
Country: Algeria
Language: English (Spanish)
Genre: Science
Published (Last): 25 May 2013
Pages: 394
PDF File Size: 20.60 Mb
ePub File Size: 7.96 Mb
ISBN: 392-3-77295-579-8
Downloads: 5577
Price: Free* [*Free Regsitration Required]
Uploader: Akinogal

This mode is entered either from pre-charge mode or constant current mode under certain conditions.

ADC Enable 1 8. V LTF-discharge Battery discharge temperature threshold set 8. Power output control 8. DC-DC3 output voltage setting 8. Key long when you grew up in the shutdown automatic datasheet feature set 0: The datasheet is incorrect here.

AXP 데이터시트(PDF) – List of Unclassifed Manufacturers

Indicates that the battery current direction 0: Coulomb Counter pause datassheet, the write will be suspended Coulomb counting while this bit is cleared from.

GPIO0 feature set 8. LDO3 output voltage settings 8. When an interrupt is fired and the interrupt line is pulled low, bit 7 of 0x48 will be set to 1.

  LEDERMAN LA PARTICULA DIVINA PDF

Battery charging in activation mode. DC-DC2 voltage rate control 1: DC-DC operating frequency is set 8. On when ADC enabled Interrupt bank 3 8.

Open After writing this bit automatically cleared each into Sleep mode again write 1. TS pin current output settings V HTF-charge Battery charging high temperature threshold settings 8.

V LTF-charge Charging the battery temperature threshold set 8. GPIO output low Indicate the charging current is less than the desired current 0: The AXP interrupt system has 2 dtaasheet for every interrupt, offset by 8 bytes. Interrupt bank 1; Input power 8. As long as the external power supply, battery or battery backup certain power exists, this data will be kept, not affected by the switch machine.

On when charging The constant current mode timeout setting Bit LDO4 output voltage settings 1. V HTF-discharge Battery discharge high temperature threshold settings 8.

Additionally, the interrupt status bit is also used to clear the interrupt, so that it can fire again. VBUS current limit control open time limit stream selection Battery activation mode may indicate that the battery is faulty. LDO3 voltage rate control 1: LDO mode, the voltage is set by the [6: Disconnect VBUS charge resistor; 1: This page was last modified on 2 Marchat The clear Coulomb Counter control bit write Coulomb Counter will be cleared while this bit is cleared from.

  FLOWSERVE CAMERON HYDRAULIC DATA PDF

DC-DC2 output voltage setting 8. To clear this interrupt, write a 1 into bit 7 of 0x Coulomb Counter Control 8. Interrupt bank 5 8.

File:AXP Datasheet v –

ADC input range 8. ADC sample rate settings, the TS pin control 8. This page has been accessed 68, times. ADC Enable 2 8.

【AXP202 X-POWERS】Electronic Components In Stock Suppliers in 2018【Price】【Datasheet PDF】USA

In battery activate mode, the charger always inputs relatively low current to batteries. AXP Chip Version 8. Charge VBUS charge feature set 0: Privacy policy About linux-sunxi. Retrieved from ” http: Close VBUS discharge resistor; 1: Personal tools Create account Log in.

Content is available under Creative Commons Attribution unless otherwise noted. Spare battery charging control 8.

admin