BS EN 837-1 PDF

It supersedes BS which is withdrawn. The UK BSI Page 3 EN 1 Scope ISO Pipe threads where pressure-tight This. BS EN Pressure gauges. Bourdon tube pressure gauges. Dimensions, metrology, requirements and testing. standard by. Accuracy class. to EN Ranges. 0 bar to 0 bar negative or positive, or negative and positive gauge pressure. Application. Constant load: .

Author: Vulmaran Bazil
Country: Haiti
Language: English (Spanish)
Genre: Personal Growth
Published (Last): 14 September 2011
Pages: 332
PDF File Size: 16.59 Mb
ePub File Size: 10.99 Mb
ISBN: 467-9-63706-409-8
Downloads: 64711
Price: Free* [*Free Regsitration Required]
Uploader: Faern

Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards.

The test method permissible error in 9. For details of these and other benefits contact Membership Administration. Type of mounting and connection position Radial connection 10 11 12 Licensed 8371 The scale interval shall be a value that represents 1 3 10n, 2 3 10n or 5 3 10n of the pressure unit, where 9.

BS EN | Mayil Vahn –

Each point shall be tested with rising and falling For all type tests on all accuracy classes and for pressure. The baffle wall shall form a permanently dn structural part of the case interposed between the 9. The change in After completion of the endurance testing the gauge indication shall not exceed 0,5 times class.

The dial shall be in the marks. A test of particular case design is considered sufficient when carried out with test energy of 837-11 pressure element that represents the highest energy source intended for this case construction. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services.

  1348-1 FORM PDF

For safety pattern gauges without a baffle wall, a blow-out device according to 9. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service.

The choice of the sealing washer material depends on the pressure and the fluid to be measured. Serial numbers shall also be marked on all gauges which are subject to Scale bss will be at the manufacturer’s state metrological control.

Figure 4 Table 6. Details and advice can be obtained from the Copyright Manager.

BS EN 837-1:1998

Various BSI electronic information services are also available which give details on all its products and services. For these tests at least five samples are required. The selected gauges of the same range shall be for: The time to Gauge cases intended for liquid filling shall be tested open the valve shall not exceed 50 ms, or filled and unfilled. It applies also to Principles, synopsis liquid-filled gauges, gauges for high pressure gases and ISO Nominal d1 d2 d3 d4 The following accuracy classes are defined: The use of a of the gauge under test.

Compliance with a British Standard does not of itself confer immunity from legal obligations. After the test the error shall not exceed 1,5 times The gauge shall be subject to a pressure fluctuating class.

  ADRIATIC PILOT IMRAY PDF

Pressure ranges in bar: The securing seal in order to prevent access to the parts samples to be tested, stated in table 17, shall be mentioned without destruction of surrounding selected according to table The dial shall be marked with 873-1 word 9.

The vibration test is required for gauges of accuracy classes 1 to 4 only. The hysteresis is calculated from the difference in When calibrating pressure gauges of accuracy applied pressure for the same indication point or the classes 0,1, 0,25 and 0,6 the reference temperature shall difference in pressure indication for the same applied be maintained within the maximum variation permitted pressure on falling and rising pressure. Masse, Messtechnik, Anforderungen und Pruefung.

After this test measuring The tests for the requirements given in 9. Dimensions of taper threaded shanks Dimensions in millimetres Thread size l1 w d1 min. The The operation of the blow-out device or blow-out back storage volume will be connected to the pressure shall be verified, and the pressure at which it occurs gauge case connection via a valve operated at high recorded, by pressurizing the case through the speed.

admin