HUAWEI CDMA BTS 3606 PDF

Default Re: Huawei CDMA E BTS Max Power??? HI I think it can be more than 20W because the RF board support MAX 60W. The 3rd Global CDMA Operation and Development Forum, themed. To illustrate this further, we can note that Huawei BTSCE power With Huawei latest CDMA BTS products, based upon the physical network. indoor type) and BTSAC (for outdoor type) are The complete series of CDMA BTSs, and relevant Thus, for the same traffic in a sector, a Huawei BTS.

Author: Zulubei Tojam
Country: Nepal
Language: English (Spanish)
Genre: Medical
Published (Last): 7 September 2011
Pages: 193
PDF File Size: 10.89 Mb
ePub File Size: 20.5 Mb
ISBN: 142-3-98097-831-5
Downloads: 75234
Price: Free* [*Free Regsitration Required]
Uploader: Maucage

Connect the other end to the DB9 socket of the power backplane. Comments to this Manuals Your Name.

Make sure that all the power modules are well connected with the backplanes, and that other boards and modules such as the CTRM and CHPA are not inserted in the slots of the backplanes. Cut the tapes along the seams of the carton cover using a knife. Installing Other Functional Modules Normally, the fan box is installed upon delivery.

Determine the length of the grounding cables according to their actual cabling path, that is, the route from the binding post of BTS cabinet to the wiring holes of the grounding protection bar of the cabinet. Chapter 4 Installing Cables introduces the categories of cables installed on site, cable distribution methods, and procedures of connecting various cdmz in BTS cabinet.

  ELECTRONICA MALVINO PDF

For the proper storage, use and disposal of this product, national laws and regulations must be observed. The engineering supervisor does not submit self-test juawei on quality of the engineering hardware. Installing Or Removing Side Doors 3. Remove four bolts and one gasket that connect the antistatic floor and the support. Anchor bolt for the floor d expansion bolt d height-lock bolt first in the middle, then on both sides To fix the support, proceed as follows: If the outer package is damaged or soaked; or the equipment is soaked btts becomes rusty, stop huawwi and find the cause.

The last section also explains how to install cabinet bfs on the cement floor without sufficient bearing capacity. If the power supply is on during the operation, do not touch the binding posts with the adjustable wrench or the screwdriver. This chapter describes how to install and use these two types of DDF. Page 43 5 M6x20 combined screw Figure Installing a cabinet on the antistatic bta Figure shows how to install a BTS cabinet on the floor without sufficient bearing capacity.

Huawei BTS3606 Installation Manual

Page of 93 Go. Tighten the bolts on the cover.

Means a complementary description. Determine the installation location for the DDF according to the engineering design for the equipment room.

Huawei CDMA E BTS Max Power ???

Select and release the primary mouse button without Click moving the pointer. Chapter 4 Installing Cables Thus, you do not need to install these cables on site. Otherwise, the equipment will suffer severe damages. When handling the cabinet, hold on the solid places such as the upper cable rack or bone frame.

  IEE GN3 PDF

To print the manual completely, please, download it. Procedure To prepare power cables, proceed as follows Enter text from picture: Lead the cables into their corresponding cable-fixing troughs. For the specific method, see section 2. Figure illustrates the positions of installation holes for U-bar supports.

To avoid damaging equipment inside, do not apply too much force.

CDMA grows greener – Huawei Publications

They are used for the convenience of installation description. GND cables for indoor cabling racks and for outdoor cabling racks.

Chapter 1 Installation Preparations introduces how to arrange the personnel arrangement, check the installation environment check, prepare project plan and make kickoff coordination, and conduct the unpacking check.

Chapter 1 Installation Preparations 1. When installing the RF cable, connect unused connectors to matching load and secure them.

Make sure the support is level and then cross-fasten the bolts of the lower support to 45 N-m in-lb with a torque wrench.

admin